
[PIM Snooping](/multicast-pim-snooping) is a feature that is supported by certain device IOS versions and platforms.  Specifically for the Cisco 9000 series devices, PIM Snooping is not supported on the CAT 9200 or 9300 series switches, but is supported on the CAT 9500 and 9600 platforms.


Multicast - PIM Snooping platform support

MPLS mandatory use of CEF

MPLS traffic engineering

MPLS-TE - why are IGPs necessary

MPLS-TE Path Message Behavior

MPLS-TE Tunnel and Recursive Routing

MPLS

MPP vs ACLs

MQTT return codes

MST - Root port selection for switches outside MST topology

MST Root Bridge Selection and Port Blocking Behavior

MST configuration revision number

MTU - Adjusting MTU to accommodate additional headers

MTU - Benefits of large L2 MTU

MTU - Interface MTU configuration considerations

MTU - Interface MTU vs IP MTU

MTU - MSS and Jumbo Frames

MTU - Path MTU Discovery (PMTUD)

MTU - Understanding L2 MTU and Frame Handling in Network Switches

MTU - default interface MTU

MTU Mismatch Test on Cisco IOS ISR4331 Routers

MTU Test on Cisco IOS ISR4331 Routers

MTU adjusting the MSS for TCP

MTU ip mtu allowed values

MTU on Etherchannel links

MTU on router subinterfaces

MTU size in Cisco IOS XR and IOS software

Management Plane Policing (MPP)

Media Access Control (MAC)

Memory - CAM and TCAM

Memory - TCAM Lookups

MetroEthernet - VLAN design considerations

MetroEthernet - Virtual Private LAN service

MetroEthernet - Virtual Private Wire Service

MetroEthernet

Multi-Topology Routing

Multicast - ASM and SSM on same network

Multicast - Any Source Multicast (ASM)

Multicast - AutoRP

Multicast - Bootstrap Router (BSR)

Multicast - Example Use Cases

Multicast - GLOP address space

Multicast - HSRP-aware PIM

Multicast - Local Network Control Block

Multicast - MSDP

Multicast - NX-OS and IOS config comparison

Multicast - PIM ALL-PIM-ROUTERS group

Multicast - PIM Bootstrap (BSR)

Multicast - PIM Control Messages

Multicast - PIM Snooping

Multicast - PIM dense vs sparse mode

Multicast - PIM join message during register stop suppression timer

Multicast - PIM

Multicast - Routing Table Timers

Multicast - Source Specific Multicast (SSM)

Multicast - Sparse Mode register suppression timer

Multicast - Understanding global vs interface-level configuration

Multicast - Upstream and Downstream

Multicast - Using MSDP with Anycast RPs

Multicast - generating a routing table entry

Multicast - ip igmp join-group vs ip igmp static-group

Multicast - reading the multicast routing table

Multicast - route-map on IOS-XE 16.9.4

Multicast - routing over the Internet

Multicast - troubleshooting multicast routing

Multicast Anycast RP

Multicast Cisco Group Management Protocol

Multicast Dense Mode Prune Message Behavior on Shared Media

Multicast IGMPv3 include and exclude modes

Multicast IPv4 address space

Multicast MAC addresses

Multicast Manual RP Configuration in Small PIM Networks

Multicast Mapping Agent and RP placement

Multicast OIL IIF mroute table

Multicast PIM Assert and dense mode

Multicast PIM Auto RP and Mapping Agent single device

Multicast PIM Bidirectional mode traffic between sources and RPs

Multicast PIM Bootstrap (BSR) election

Multicast PIM Designated Router sparse mode

Multicast PIM Route Pruning and SPT-Threshold

Multicast PIM dense mode

Multicast PIM neighbors are stateless

Multicast PIM send-rp-announce-scope

Multicast PIM sparse mode Rendezvous Point (RP)

Multicast PIM sparse mode

Multicast PIM sparse-dense mode

Multicast PIM what triggers an assert forwarder election

Multicast PIM with multiple RPs

Multicast PIM with multiple mapping-agents

Multicast PIM-assert forwarder election

Multicast SPT and RPT

Multicast bidirectional PIM advantages

Multicast boundary filtering - filter auto RP

Multicast enabling Bidir in BSR mode

Multicast ip pim autorp listener

Multicast ip pim rp-address override

Multicast load splitting across equal-cost paths

Multicast local subnetwork address range

Multicast mapping IP to MAC addresses