OSPF network types

OSPF


[OSPF](/ospf) considers any [GRE](/gre) multipoint tunnel interface as a point-to-point network type.  If no network type is configured, the default for such an interface is point-to-point.

Links:

https://forum.networklessons.com/t/dmvpn-phase-2-ospf-routing/1309/17?u=lagapides

OSPF in a GRE multipoint environment

OSPF - default-information originate always command

OSPF - distribute-list filtering

OSPF - manual neighbor configuration

OSPF - point-to-multipoint network type

OSPF - route filtering

OSPF - route summarization

OSPF - summary-address nssa-only on an ABR

OSPF - what triggers a DR-BDR election

OSPF ABR Type 3 LSA filtering using access lists

OSPF ABR and Loop Prevention

OSPF Authentication for v2 and v3

OSPF DR BDR election and neighbor adjacencies

OSPF DR BDR election criteria

OSPF DR BDR election process

OSPF Design - When to create new instance

OSPF Determining which LSA is newer

OSPF Discontiguous Area 0

OSPF E1 E2 N1 N2 routes

OSPF Forwarding Address

OSPF Hello packets unicast and multicast

OSPF IP Unnumbered

OSPF IS-IS comparison

OSPF Incremental SPF and receipt of LSAs

OSPF LSA Recursion

OSPF LSA Sequence Numbers

OSPF LSA Types

OSPF NSSA ABR advertises default route

OSPF Not So Stubby Area NSSA

OSPF Path selection

OSPF Routing Bit

OSPF SPF Scheduling and throttling timers

OSPF TTL Security Check

OSPF Troubleshooting

OSPF Type 4 LSA

OSPF Type 5 LSA

OSPF Type 7 LSA

OSPF Why it is not suitable for use on the Internet

OSPF advertising loopback network

OSPF area inactive

OSPF area notation

OSPF area type mismatch

OSPF backbone area 0

OSPF default metric values

OSPF design - when to create a new area

OSPF does not redistribute default route

OSPF downheap LSA

OSPF duplicate router IDs

OSPF extent of reconvergence process

OSPF immediate hello packet

OSPF loop prevention

OSPF master slave election

OSPF message options field

OSPF metric sum of outgoing interface costs

OSPF modifying the router ID

OSPF network command

OSPF non directly connected neighbor adjacencies

OSPF packet types

OSPF point to point network type for Ethernet

OSPF requirements for forming adjacency

OSPF router ID in an IPv6 environment

OSPF router ID

OSPF sham-link cost

OSPF sham-link

OSPF virtual link and ABRs

OSPF where do you configure a virtual link

OSPF why is a backbone area 0 necessary

OSPF within what area is an OSPF router considered to be

OSPFv2 and OSPFv3 comparison

OSPFv3 - router ospfv3 command

OSPFv3 communication between routers and next hop addresses

OSPFv3 instance ID

Offset-list

PAT (overloading) maximum number of translations per inside global address

PAgP

PBR - Policy Based Routing

PBR - Transport Layer port number

PBR - load balancing

PBR - matching prefix lists

PBR - route-map and ACL deny statements not supported

PBR - set interface command

PBR next hop recursive

PBR next hop verify availability

PBR next-hop and default next-hop

PPPoE

PSTN

PTP - Best Master Clock Algorithm

PTP - Clock Types

PTP - Interface Roles

PTP - Offset and Delay times

PTP - Precision Time Protocol

Passive interface

Physical layer - Copper medium

Physical layer - Optical fiber medium

Physical layer - Wireless medium

Physical layer - carrier wave

Physical layer - encoding

Physical layer - media

OSPF in a GRE multipoint environment

Links to this page: