Multicast Mapping Agent and RP placement

Multicast PIM send-rp-announce-scope


When implementing [multicast](/multicast), the `scope` keyword is used to specify the TTL in the IP header of [Auto-RP](/multicast-autorp) discovery messages.  For the `scope` keyword and `ttl-value` argument, specify a TTL large enough to cover your [Protocol Independent Multicast (PIM)](/protocol-independent-multicast-pim) domain.

[Multicast PIM send-rp-announce-scope](/multicast-pim-send-rp-announce-scope)

Links:

https://forum.networklessons.com/t/multicast-pim-sparse-dense-mode/2825/16?u=lagapides
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti/command/imc-cr-book/imc_i3.html#wp8174277210

Media Access Control (MAC)

Memory - CAM and TCAM

Memory - TCAM Lookups

MetroEthernet - VLAN design considerations

MetroEthernet - Virtual Private LAN service

MetroEthernet - Virtual Private Wire Service

MetroEthernet

Multi-Topology Routing

Multicast - ASM and SSM on same network

Multicast - Any Source Multicast (ASM)

Multicast - AutoRP

Multicast - Bootstrap Router (BSR)

Multicast - Example Use Cases

Multicast - GLOP address space

Multicast - HSRP-aware PIM

Multicast - Local Network Control Block

Multicast - MSDP

Multicast - NX-OS and IOS config comparison

Multicast - PIM Bootstrap (BSR)

Multicast - PIM Snooping platform support

Multicast - PIM Snooping

Multicast - PIM dense vs sparse mode

Multicast - PIM join message during register stop suppression timer

Multicast - PIM

Multicast - Routing Table Timers

Multicast - Source Specific Multicast (SSM)

Multicast - Sparse Mode register suppression timer

Multicast - Understanding global vs interface-level configuration

Multicast - Upstream and Downstream

Multicast - generating a routing table entry

Multicast - ip igmp join-group vs ip igmp static-group

Multicast - reading the multicast routing table

Multicast - route-map on IOS-XE 16.9.4

Multicast - routing over the Internet

Multicast - troubleshooting multicast routing

Multicast Anycast RP

Multicast Cisco Group Management Protocol

Multicast IGMPv3 include and exclude modes

Multicast IPv4 address space

Multicast MAC addresses

Multicast OIL IIF mroute table

Multicast PIM Assert and dense mode

Multicast PIM Auto RP and Mapping Agent single device

Multicast PIM Bidirectional mode traffic between sources and RPs

Multicast PIM Bootstrap (BSR) election

Multicast PIM Designated Router sparse mode

Multicast PIM dense mode

Multicast PIM neighbors are stateless

Multicast PIM sparse mode Rendezvous Point (RP)

Multicast PIM sparse mode

Multicast PIM sparse-dense mode

Multicast PIM with multiple RPs

Multicast PIM with multiple mapping-agents

Multicast PIM-assert forwarder election

Multicast SPT and RPT

Multicast bidirectional PIM advantages

Multicast boundary filtering - filter auto RP

Multicast enabling Bidir in BSR mode

Multicast ip pim autorp listener

Multicast ip pim rp-address override

Multicast load splitting across equal-cost paths

Multicast local subnetwork address range

Multicast mapping IP to MAC addresses

Multicast mapping agent IGMP membership report

Multicast ping on a Nexus device

Multicast using Anycast RP with Auto-RP and BSR

Multicast

NAT - Translation Table

NAT - Twice NAT

NAT - Understanding debug nat detailed output

NAT - Virtual Interface (NVI)

NAT - What is Policy NAT

NAT - add-route keyword

NAT - ports used for translation

NAT - show NAT translations

NAT - translate address not directly connected to edge device

NAT Extendable on Cisco IOS

NAT Order of Operation

NAT address naming conventions

NAT and IPv6

NAT how port numbers are chosen when using PAT

NAT intra-VRF NAT

NAT port forwarding - specifying outside IP address

NAT prefix-length keyword on nat pool command

NAT vrf-aware

NBAR classifies only established sessions

NETCONF

NHRP - Authentication

NHRP - Destination Protocol Address

NHRP - Holding Time

NHRP - resolution redirect from hub

NHRP show ip nhrp flags

NHRP

NTP - securing with MD5 authentication and a Windows NTP server

NTP poll interval

NTP server and client and the master command

NTP troubleshooting and debugging tools

NTP versions 3 and 4

Multicast PIM send-rp-announce-scope

Links to this page: